I think part of the problem is a fundamental misunderstanding of what parachuting into the ocean does to a rocket motor. The motors are the expensive part of the first stage; I don’t know exact numbers, but they are the complicated, intricate, extremely-high-precision parts that must be exactly right or everything goes boom. The tank, by comparison, is an aluminum can.
The last landing attempt failed because a rocket motor’s throttle valve had a bit more static friction than it should, and stuck open a moment too long. SpaceX’s third launch attempt—the last failed launch they’ve had, many years ago with the Falcon 1 - was because the motor didn’t shut off instantly before stage separation, like it should have. As far as I know, people still don’t know why Orbital ATK (FKA Orbital Science)’s last launch attempt failed, except that it was obviously an engine failure. We talk about rocket science, but honestly the theoretical aspects of rocketry aren’t that complicated. Rocket engineering, though, that’s a bloody nightmare. You get everything as close to perfect as you can, and sometimes it still fails catastrophically and blows away more value than most of the people reading this thread will earn in their lifetimes, leaving virtually nothing to tell the tale of what happened.
What does all that have to do with parachute recovery of booster stages? Well, once you’ve dunked those motors in saltwater, they’re a write-off. They can’t be trusted to ever again operate perfectly without fairly literally rebuilding them, which defeats most of the purpose of recovering the booster.
There’s nothing you could coat a rocket motor with that would both survive that motor operating and make it economical to re-use the motor after plunging into the ocean. The closest thing I can think of would be some kind of protective bubble that expands to protect the motors from the ocean once their job is done. It would need to be watertight, impact-resistant (the rocket still hits the water pretty hard, even with parachutes), able to deploy around the motors reliably, avoid causing a bending moment that collapses the tank (which has minimal pressure, because its fuel is depleted and any excess pressurizing agent you carry is wasted weight to orbit), and able to operate after being exposed to the environment in close proximity to a medium-lift rocket’s primary launch motors. Maybe it’s possible, but I can’t think of how to do reliably enough to be worth the added cost on launch.
I think part of the problem is a fundamental misunderstanding of what parachuting into the ocean does to a rocket motor. The motors are the expensive part of the first stage; I don’t know exact numbers, but they are the complicated, intricate, extremely-high-precision parts that must be exactly right or everything goes boom. The tank, by comparison, is an aluminum can.
The last landing attempt failed because a rocket motor’s throttle valve had a bit more static friction than it should, and stuck open a moment too long. SpaceX’s third launch attempt—the last failed launch they’ve had, many years ago with the Falcon 1 - was because the motor didn’t shut off instantly before stage separation, like it should have. As far as I know, people still don’t know why Orbital ATK (FKA Orbital Science)’s last launch attempt failed, except that it was obviously an engine failure. We talk about rocket science, but honestly the theoretical aspects of rocketry aren’t that complicated. Rocket engineering, though, that’s a bloody nightmare. You get everything as close to perfect as you can, and sometimes it still fails catastrophically and blows away more value than most of the people reading this thread will earn in their lifetimes, leaving virtually nothing to tell the tale of what happened.
What does all that have to do with parachute recovery of booster stages? Well, once you’ve dunked those motors in saltwater, they’re a write-off. They can’t be trusted to ever again operate perfectly without fairly literally rebuilding them, which defeats most of the purpose of recovering the booster.
There’s nothing you could coat a rocket motor with that would both survive that motor operating and make it economical to re-use the motor after plunging into the ocean. The closest thing I can think of would be some kind of protective bubble that expands to protect the motors from the ocean once their job is done. It would need to be watertight, impact-resistant (the rocket still hits the water pretty hard, even with parachutes), able to deploy around the motors reliably, avoid causing a bending moment that collapses the tank (which has minimal pressure, because its fuel is depleted and any excess pressurizing agent you carry is wasted weight to orbit), and able to operate after being exposed to the environment in close proximity to a medium-lift rocket’s primary launch motors. Maybe it’s possible, but I can’t think of how to do reliably enough to be worth the added cost on launch.